Stab and Shock Resistant Anti Riot Armour for Police
This stab and shock resistant anti riot armour is a full police riot suit built to absorb blunt force and resist knife thrusts during crowd control. Its contour moulded shell has raised impact ridges that spread the energy of a blow, and foam padding underneath cushions the body. We manufacture it in China and export it to police, army and tender buyers.
Coverage and fastening strength
The suit covers a listed protect area of 1.08m2, split across the back (≥0.1), arms (≥0.18) and legs (≥0.30), with the chest, abdomen and groin listed at ≥0.1. The panels are usually segmented and joined by hook-and-loop or buckle body straps, so an officer can move, crouch and run in formation.
Strap strength is often where cheaper riot gear fails first. For this model the table lists Velcro grip above 7.2N/cm2, buckle strength above 500N and joint strength above 2000N. Plates are typically high-density polyethylene or polycarbonate over impact foam, while soft brush and mesh lining reduce rubbing on long shifts.
Stab and shock resistant anti riot armour test claims
The maker states the following results for this suit:
- A dagger pressed on any point of the chest, back or groin at 2000N static pressure for one minute does not pierce it (≥ 20J)
- A 7.5kg steel ball dropped again and again on the chest and arms from 163cm leaves no flaw (≥ 20J)
- Performance holds between -20 °C and +55 °C
The shell is also described as fire and acid resistant. We pass these figures on as the manufacturer's data and send the test papers for your batch on request; we do not claim a rating that has not been confirmed for your order.
Buying for a tender or a bulk issue
Riot units usually order a mix of sizes plus spare arm and leg guards. We confirm the size split, colour, carry bag and Incoterm before production and pack suits in seaworthy export crating. Orders ship to Nigeria, Kenya, Ghana and more than 60 other countries, with the invoice, packing list and certificate of origin. Our page on certifications and compliance documents explains how we handle tender paperwork.
Other riot suits to compare
For a suit with an 11-part layout, see the rigid inner panel anti riot armour. A lighter set with a baton is the flame resistance full body armor with T baton. You can also browse all army equipment. Each stab and shock resistant anti riot armour order is quoted by quantity and destination port.
| Category | Army Equipment |
| Sub-category | Anti Riot Armour |
| Power / Mechanism | Segmented panel construction with hook-and-loop or buckle body straps * |
| Build Material | High-density polyethylene or polycarbonate plates over impact-foam padding * |
| Capacity / Size | Stab, blunt-impact and fragment protection to typical riot-control duty levels * |
| Protect Area | 1.08m2 |
| - Back | ≥0.1 |
| - Arms | ≥0.18 |
| - Legs | ≥0.30 |
| - Velcro | >7.2N/cm2 |
| - Buckle | >500N |
| - Joints | >2000N |
| Availability | In stock / Made to order |
| Export Packaging | Seaworthy export crating available |
| Warranty | As per manufacturer terms — confirm at enquiry |
* Typical value for this type of equipment, not an exact datasheet figure for one specific unit — confirm the precise specification for your order at enquiry.
Compare
How this compares to similar Army Equipment products
| Model | Automation / Power | Material | Capacity |
|---|---|---|---|
| Army Police Riot Gear Anti Riot Armour With Stab Resistant Shock Resistant (this page) | Segmented panel construction with hook-and-loop or buckle body straps | High-density polyethylene or polycarbonate plates over impact-foam padding | Stab, blunt-impact and fragment protection to typical riot-control duty levels |
| Army 8-9 KGS Riot Police Armor Fire Stab And Impact Protection For Crowd Control | Segmented panel construction with hook-and-loop or buckle body straps | High-density polyethylene or polycarbonate plates over impact-foam padding | Stab, blunt-impact and fragment protection to typical riot-control duty levels |
| Army ABS And PC Plastic Anti Riot Armour Hard Shell With Foam Inner Padding | Segmented panel construction with hook-and-loop or buckle body straps | Plastic | Stab, blunt-impact and fragment protection to typical riot-control duty levels |
| Army Flame Resistance Body Anti Riot Armour Full Body Armor With T Baton | Segmented panel construction with hook-and-loop or buckle body straps | High-density polyethylene or polycarbonate plates over impact-foam padding | Stab, blunt-impact and fragment protection to typical riot-control duty levels |
You may also need
Related products
Army 8-9 KGS Riot Police Armor Fire Stab And Impact Protection For Crowd Control
View details →
Army ABS And PC Plastic Anti Riot Armour Hard Shell With Foam Inner Padding
View details →
Army Flame Resistance Body Anti Riot Armour Full Body Armor With T Baton
View details →
Army Free Size Riot Gear Body Armor , Black Military Body Armor With T Baton
View details →Buyer FAQs
Questions about the Army Police Riot Gear Anti Riot Armour With Stab Resistant Shock Resistant
Yes — capacity, power specification and accessories for the Army Police Riot Gear Anti Riot Armour With Stab Resistant Shock Resistant can typically be configured to your requirement. Share your target output and destination country when you enquire.
Export orders are supplied with seaworthy packaging, shipment documentation and, where applicable, an operating manual. Installation and after-sales terms are confirmed at order stage.
Export coverage for this category extends to 67+ countries across Africa, Asia, the Middle East and Latin America; share your destination port for a shipping estimate.
Yes — tender and government-order supply is a regular part of our export business. Send the Army Police Riot Gear Anti Riot Armour With Stab Resistant Shock Resistant specification from your tender document along with the required quantity and delivery window, and we'll confirm pricing, certification paperwork and a delivery plan.